Toward respiratory support of critically ill COVID-19 patients using repurposed kidney hollow fiber membrane dialysers to oxygenate the blood

A. Theoretical considerations and computational methodology

Mass transfer in the HFMD is modelled by the following equation: where, k₀ is the mass transfer coefficient, A is the membrane area, qO₂ is the rate of oxygen transferred and LMΔpO₂ is the logarithmic mean of partial pressure differences at the top and bottom of the device.

Defining the partial pressure difference between the blood inlet and the oxygen flow outlet as , and between the blood outlet and oxygen flow inlet as , and expanding the definition of logarithm mean, the expression for the mass transfer coefficient × Area (k₀A) becomes:

To achieve a given qO₂, this equation facilitates determination of the minimum k₀A of the device.

As oxygen transport capacity of blood resides primarily in haemoglobin, it reaches saturation at a low partial pressure of oxygen. Thus we can assume that oxygen transfer into blood takes place within a narrow range of partial pressures. Also, for high-purity oxygen, the pO₂ may be regarded as essentially constant.

The oxygen carrying capacity of blood is 8800μM of O₂ bound to the Hb for 100% saturation [10] and dissolved O₂ in blood is negligible. The HFMD cartridges are designed for blood flow-rates up to 500 ml/min, and we evaluate oxygen-carrying capacity of blood for a Hb concentration of 15g/100ml and a typical oxyhaemoglobin dissociation curve.

At sea level atmospheric pressure, and for a typical venous and arterial pO₂ of 6 and 12.7 kPa (and corresponding HbSat of 45% and 95%) respectively, the oxygen uptake in 500 ml of blood and the and are calculated and substituted into (2) to estimate the required k₀A. This is repeated for an inlet venous HbSat of 25% as shown in Table I.

It is assumed that mass transfer across the membrane is rate limiting rather than blood mass transfer or the reaction of oxygen with haemoglobin.

B. Materials and methods for gas transfer into water

The experiments were conducted at the Biotechnology Laboratory at UNISA, Johannesburg at an altitude of about 1700m with atmospheric pressure about 84kPa and temperature about 25^oC.

A low-flux Leoceed-21N (Asahi Kasei Medical) hollow fiber membrane dialyser unit renal dialysis cartridge was used in this study. The polysulfone membrane has an effective surface area of 2.1 m², and the HFMD has a priming volume of 108 ml, and an internal fibre diameter and wall thickness of 185 μm and 35 μm respectively. The manufacturer-specified maximum blood flow rate is 500 ml · min⁻¹ (mean residence time about 13s at this flow rate). Maximum transmembrane pressure (TMP) is rated at 80kPa.

Tap water was deoxygenated by boiling and allowed to cool in a sealed glass bottle, and measured for dissolved oxygen (SD 400 OXI L, Lovibond, Amesbury, UK). The deoxygenated water was pumped through the vertically mounted HFMD using a peristaltic pump (Qdos Chemical metering pumps, Watson Marlow, Cornwell, UK) via the blood inlet at 50, 200 and 500 ml · min⁻¹ and discharged into a beaker covered with parafilm to minimize oxygen losses.

High-purity (>99%) oxygen (Afrox gas, Johannesburg, South Africa) was passed counter-current through the HFMD via the dialysate inlet, using a pressure regulator set between 60 to 80 kPa (gauge) followed by a needle valve to control flow rate at 400 ml · min⁻¹.

C. Materials and methods for gas transfer into blood

This study with human blood was approved by the institutional review board of the South African National Blood Services Human Research Ethics Committee (certificate number: 2019/0521), and the institutional review board of the University of the Witwatersrand, Johannesburg Human Research Ethics Committee (Medical) (certificate number: M200456). The experiments were conducted at the Chemical Pathology Laboratory, University of the Witwatersrand, Johannesburg, at an altitude of about 1500 m (atmospheric pressure about 85kPa).

Recently expired donor whole blood (SANBS) was warmed in a water bath at 37^oC and pooled in a glass flask to constitute approximately 4.5 l to which approximately 3000 units of heparin (Heparin sodium mucosal Fresenius Kabi, 5ml of 1000 U/ml) was added.

• Download figure
• Open in new tab

Fig. 1.

Flowsheet of experimental setup with blood. The oxygen was passed through the dialyser via the dialysate inlet while deoxygenated blood was passed through the hollow fibres in counter-current to the oxygen flow.

Nitrogen sparge gas was bubbled through the blood to reduce the % oxygen saturation of haemoglobin (HbSat) to typical venous levels [11]. The nitrogen flow was gradually increased from 1 l/min until froth was visualised,

As shown in Figure 1, blood was pumped by a roller pump through the hollow fibers of a vertically-mounted HFMD, from top to bottom, at 500 ml/min. The upstream placement of the roller pump reduces the risk of red blood cell lysis prior to oxygenation. Blood was discharged into a collecting flask. Oxygen was passed counter-current at 1250 ml/min through the outside of the fibers.

The pump was placed ≈ 0.5 m below the base of the HFMD to achieve a pressure head, thus reducing the required suction, making sampling easier. The blood was piped through dialysis tubing fitted with inlet and outlet sampling ports (Fresenius Kabi).

After priming with normal saline, flow was switched to blood which was mixed by swirling, prior to and during the experiments.

Two runs were performed using a Leoceed-21N (Asahi Kasei Medical) HFMD and the third run using a Leoceed-18N (effective surface areas of 1.8 m², priming volume 96 ml). A high-flux Leoceed H-type dialyser was also tested but fluid leakage across the membrane into the gas side was noted, suggesting that this high-flux dialyser may not be suitable for oxygenation.

Two to four inlet and outlet blood samples of 1 - 4 ml each were taken for each run with heparin-coated syringes, and analysed with a blood gas analyser (Radiometer, ABL80 FLEX CO-OX) for Haemoglobin concentration (Hb), partial pressure of carbon dioxide (pCO₂), partial pressure of oxygen (pO₂), and haemoglobin saturation (HbSat). Bicarbonate ion concentrations () were calculated by the blood gas analyser.

Measurements were averaged for each run over the sample number. Measurement uncertainties were reported as ± 1 standard deviation based on rounded estimates from coefficients of variation [12], [13] and scaled for sample number.

A. Experiments with water

Oxygen was passed through the HFMD at 400 ml/min and water was run counter-current through the inside of the hollow fibers. Inlet oxygen concentration was measured at 3.61 mg/l, at 37.1C.

Outflow water was collected in beakers and oxygen concentration measured. Table II shows these data and corresponding calculated oxygen transfer rates.

The low reading of 28.6mg · l⁻¹ is probably due to higher overall oxygen losses at saturation due to the slower flow rate.

Equation (2) is used to estimate k₀A based on the minimum oxygen transfer rate of 14.6mg · min⁻¹ at 500ml · min⁻¹. Dissolved oxygen concentration is treated as negligible as haemoglobin carries most of the oxygen.

The oxygen exit stream is at atmospheric pressure, and the water inlet’s partial pressure is given by the % saturation read from the dissolved oxygen meter × pO₂ in air at 84kPa, which amounts to a difference of . The oxygen outlet pressure has little influence on the large driving force for mass transfer.

The requires knowledge of the unmeasured gas pressure as it enters the HFMD. The pressure regulator reading was 60kPa but most of the pressure drop occurs at the needle valve. Also, prior to membrane contact there was a contractor connection and the expansion/elbow entering the membrane unit, whereas on the discharge side there was just the expansion/elbow and a short length of tubing to the discharge. While it is not possible to exactly know the pressure in the membrane unit, it must be considerably lower than the regulator’s pressure reading, and a simple estimate suggest that the relevant pressure drop is as low as 0.1kPa.

Because the outlet water stream is at or above saturation, the partial pressure difference at that point is at most equal to that over-pressure amount. Thus the mass transfer coefficient calculations are highly sensitive to the actual pressure in this region.

For a 0.1 kPa partial pressure drop across the , and a minimum oxygen transfer rate measured at 14.6mg/min, equation (2) yields a k₀A value of 1.334 mg · min⁻¹ · kPa⁻¹. This implies a 3.4 fold larger oxygen mass transfer rate than required to fully oxygenate blood to 95 % saturation for incoming pO₂ of 45 mmHg, and 1.7 fold larger than needed if the incoming pO₂ is 25 mmHg.

Even in the unlikely case of a of 6kPa, the potential mass transfer rate of oxygen will be 1.4 fold larger than the minimum needed for incoming blood with oxygen partial pressure of 45 mmHg and 70% of the required amount for an incoming saturation of 25 mmHg.

B. Results for gas transfer in blood

As seen in figure 2, the dark blood entering the top and bright red blood exiting from the bottom of the HFMD is clear evidence of oxygenation.

Measurements from the inlet and outlet ports from two runs using a Leoceed-21N HFMD and one run using the Leoceed-18N HFMD are shown in table III. Samples (n = 2 to 4) were averaged and reported ± one standard deviation measurement uncertainty.

Measurement uncertainties for the blood gas analyser were approximated as 1% for pO₂, pCO₂ and Hb, and 0.1% for HbSat based on reported coefficient of variation data [12], [13]. The high values for pCO₂ are in keeping with known changes in stored blood [14].

• Download figure
• Open in new tab

Fig. 2.

Vertically-mounted Leoceed-21N HFMD showing dark deoxygenated blood entering the device at the top and bright red oxygenated blood exiting from the bottom of the device.

Oxygen content per 100 ml of blood () was calculated using a conservative Hufner constant of 1.31 as follows [15]:

Substituting the differential values for HbSat and pO₂ between inlet and outlet into (3), the oxygen transfer rate () in ml(STP) · min⁻¹ for a blood flow rate of 500 ml/min was calculated as shown in table IV. This table also shows the % of the nominal 250 ml(STP) · min⁻¹ oxygen consumption rate () and the % maximum (100 % HbSat at outlet at prevailing Hb) oxygen transfer rate ().

Highest oxygen transfer rates were obtained on Run 1 with the 21N HFMD. Run 2 utilising the same HFMD showed diminished oxygen transfer rates compared to Run 1, probably due to fouling of the HFMD which was noted prior to the second run. Run 3 with the 18N HFMD showed the lowest oxygen transfer rates which is consistent with the smaller surface area.

Using equation (2), mass transfer coefficient × Area product (k₀A) estimates for oxygen were 0.72, 0.56 and 0.69. mg · kPa⁻¹ · min⁻¹ for runs 1, 2 and 3 respectively. These estimates are in close agreement with theoretical k₀A estimates for blood which ranged from 0.389 to 0.787 mg · kPa⁻¹min⁻¹. These estimates are also in keeping with minimum estimated k₀A of 1.33 mg · kPa⁻¹min⁻¹ for minimum oxygen transfer rate of 14.6 mg · min⁻¹ determined in the water experiments.

Mass transfer estimates for carbon dioxide

While the principle purpose of this study is blood oxygenation, CO₂ elimination is also an important consideration.

The outlet partial pressure of CO₂ was estimated by performing a CO₂ mass balance using pCO₂ and , together with the oxygen flow rate of 1250 ml/min.

From the pCO₂ and concentrations at the inlet and outlet on each run, and treating CO₂ binding to Hb as negligible, TotalCO₂ concentrations were calculated as shown in table V. Using equation (2), k₀A for CO₂ was estimated for runs 1, 2 and 3 as 6.0, 6.6 and 19.4 mg · kPa⁻¹ · min⁻¹ respectively. The 3-fold higher value for the 18N dialyser is probably due to the sensitivity of the calculation to the indirectly estimated outlet pCO₂, and uncertainties in the bicarbonate concentrations which are calculated rather than directly measured by the ABL80 FLEX CO-OX.